Hdparm: differenze tra le versioni

Vai alla navigazione Vai alla ricerca

Hdparm (visualizza wikitesto)

Versione delle 15:50, 19 mag 2005

18 821 byte aggiunti ,  19 mag 2005
preparate le opzioni da tradurre e commentare
(bozza e indice)
 
(preparate le opzioni da tradurre e commentare)
Riga 4: Riga 4:
=Cosa serve=
=Cosa serve=
==Installazione==
==Installazione==
Il pacchetto presente in Debian:
<pre>
# apt-get install hdparm
</pre>
==Kernel==
==Kernel==
Per poter utilizzare al meglio questo strumento, consigliato:
* avere una versione del kernel abbastanza recente (quelle presenti in Sarge vanno pi che bene)
* avere i moduli per il proprio chipset caricati (o compilati staticamente nel kernel)


=Opzioni e Argomenti=
=Opzioni e Argomenti=
Le opzioni disponibili sono tante, alcune delle quali '''critiche''', quindi sconsiglio vivamente l'utilizzo di opzioni che non si conoscono, per evitare danni e/o malfunzionamenti/perdite di dati... (declino ogni responsabilit su questi).
:'''-a'''    Get/set sector count for filesystem read-ahead.  This is used to improve performance in sequential reads of large files, by  prefetching  additional
              blocks  in  anticipation  of  them being needed by the running task.  In the current kernel version (2.0.10) this has a default setting of 8 sectors
              (4KB).  This value seems good for most purposes, but in a system where most file accesses are random seeks, a smaller setting might  provide  better
              performance.  Also, many IDE drives also have a separate built-in read-ahead function, which alleviates the need for a filesystem read-ahead in many
              situations.
      -A    Disable/enable the IDE drive's read-lookahead feature (usually ON by default).  Usage: -A0 (disable) or -A1 (enable).
      -b    Get/set bus state.
      -B    Set Advanced Power Management feature, if the drive supports it. A low value means aggressive power management and a high value means better perfor-
              mance. A value of 255 will disable apm on the drive.
      -c    Query/enable  (E)IDE 32-bit I/O support.  A numeric parameter can be used to enable/disable 32-bit I/O support: Currently supported values include 0
              to disable 32-bit I/O support, 1 to enable 32-bit data transfers, and 3 to enable 32-bit data transfers with a special  sync  sequence  required  by
              many  chipsets.  The value 3 works with nearly all 32-bit IDE chipsets, but incurs slightly more overhead.  Note that "32-bit" refers to data trans-
              fers across a PCI or VLB bus to the interface card only; all (E)IDE drives still have only a 16-bit connection over the ribbon cable from the inter-
              face card.
      -C    Check  the current IDE power mode status, which will always be one of unknown (drive does not support this command), active/idle (normal operation),
              standby (low power mode, drive has spun down), or sleeping (lowest power mode, drive is completely shut down).  The -S, -y, -Y, and -Z flags can  be
              used to manipulate the IDE power modes.
      -d    Disable/enable the "using_dma" flag for this drive.  This option now works with most combinations of drives and PCI interfaces which support DMA and
              which are known to the kernel IDE driver.  It is also a good idea to use the appropriate -X option in combination with -d1 to ensure that the  drive
              itself is programmed for the correct DMA mode, although most BIOSs should do this for you at boot time.  Using DMA nearly always gives the best per-
              formance, with fast I/O throughput and low CPU usage.  But there are at least a few configurations of chipsets and drives for  which  DMA  does  not
              make much of a difference, or may even slow things down (on really messed up hardware!).  Your mileage may vary.
      -D    Enable/disable the on-drive defect management feature, whereby the drive firmware tries to automatically manage defective sectors by relocating them
              to "spare" sectors reserved by the factory for such.
      -E    Set cdrom speed.  This is NOT necessary for regular operation, as the drive will automatically switch speeds on its own.  But if you  want  to  play
              with it, just supply a speed number after the option, usually a number like 2 or 4.
      -f    Sync and flush the buffer cache for the device on exit.  This operation is also performed as part of the -t and -T timings.
      -g    Display the drive geometry (cylinders, heads, sectors), the size (in sectors) of the device, and the starting offset (in sectors) of the device from
              the beginning of the drive.
      -h    Display terse usage information (help).
      -i    Display the identification info that was obtained from the drive at boot time, if available.  This is a feature of modern IDE drives, and may not be
              supported by older devices.  The data returned may or may not be current, depending on activity since booting the system.  However, the current mul-
              tiple sector mode count is always shown.  For a more detailed interpretation of the identification info, refer to AT Attachment Interface  for  Disk
              Drives (ANSI ASC X3T9.2 working draft, revision 4a, April 19/93).
-I    Request  identification  info directly from the drive, which is displayed in a new expanded format with considerably more detail than with the older
              -i flag.
      -Istdin
              This is a special "no seatbelts" variation on the -I option, which accepts a drive identification  block  as  standard  input  instead  of  using  a
              /dev/hd*  parameter.  The  format of this block must be exactly the same as that found in the /proc/ide/*/hd*/identify "files", or that produced by
              the -Istdout option described below.  This variation is designed for use with collected "libraries" of drive  identification  information,  and  can
              also be used on ATAPI drives which may give media errors with the standard mechanism.
      -Istdout
              This  option  simply  dumps the identify data in hex to stdout, in a format similar to that from /proc/, and suitable for later use with the -Istdin
              option.
      -k    Get/set the keep_settings_over_reset flag for the drive.  When this flag is set, the driver will preserve the -dmu options over a  soft  reset,  (as
              done  during  the  error  recovery sequence).  This flag defaults to off, to prevent drive reset loops which could be caused by combinations of -dmu
              settings.  The -k flag should therefore only be set after one has achieved confidence in correct system operation with a chosen set of configuration
              settings.  In practice, all that is typically necessary to test a configuration (prior to using -k) is to verify that the drive can be read/written,
              and that no error logs (kernel messages) are generated in the process (look in /var/adm/messages on most systems).
      -K    Set the drive's keep_features_over_reset flag.  Setting this enables the drive to retain the settings for -APSWXZ over a soft reset (as done  during
              the error recovery sequence).  Not all drives support this feature.
      -L    Set the drive's doorlock flag.  Setting this to 1 will lock the door mechanism of some removable hard drives (eg. Syquest, ZIP, Jazz..), and setting
              it to 0 will unlock the door mechanism.  Normally, Linux maintains the door locking mechanism automatically, depending on drive usage (locked  when-
              ever  a filesystem is mounted).  But on system shutdown, this can be a nuisance if the root partition is on a removeable disk, since the root parti-
              tion is left mounted (read-only) after shutdown.  So, by using this command to unlock the door after the root filesystem is remounted read-only, one
              can then remove the cartridge from the drive after shutdown.
      -m    Get/set  sector  count for multiple sector I/O on the drive.  A setting of 0 disables this feature.  Multiple sector mode (aka IDE Block Mode), is a
              feature of most modern IDE hard drives, permitting the transfer of multiple sectors per I/O interrupt, rather than the usual one sector  per  inter-
              rupt.  When  this  feature  is  enabled,  it typically reduces operating system overhead for disk I/O by 30-50%.  On many systems, it also provides
              increased data throughput of anywhere from 5% to 50%.  Some drives, however (most notably the WD Caviar series), seem to run  slower  with  multiple
              mode  enabled.  Your mileage may vary.  Most drives support the minimum settings of 2, 4, 8, or 16 (sectors).  Larger settings may also be possible,
              depending on the drive.  A setting of 16 or 32 seems optimal on many systems.  Western Digital recommends lower settings of 4 to 8 on many of  their
              drives,  due  tiny (32kB) drive buffers and non-optimized buffering algorithms.  The -i flag can be used to find the maximum setting supported by an
              installed drive (look for MaxMultSect in the output).  Some drives claim to support multiple mode, but lose data at some settings.  Under rare  cir-
              cumstances, such failures can result in massive filesystem corruption.
      -M    Get/set  Automatic  Acoustic Management (AAM) setting. Most modern harddisk drives have the ability to speed down the head movements to reduce their
              noise output.  The possible values are between 0 and 254. 128 is the most quiet (and therefore slowest) setting and 254 the fastest  (and  loudest).
              Some  drives  have only two levels (quiet / fast), while others may have different levels between 128 and 254.  THIS FEATURE IS EXPERIMENTAL AND NOT
              WELL TESTED. USE AT YOUR OWN RISK.
      -n    Get or set the "ignore write errors" flag in the driver.  Do NOT play with this without grokking the driver source code first.
      -p    Attempt to reprogram the IDE interface chipset for the specified PIO mode, or attempt to auto-tune for the "best" PIO mode supported by  the  drive.
              This feature is supported in the kernel for only a few "known" chipsets, and even then the support is iffy at best.  Some IDE chipsets are unable to
              alter the PIO mode for a single drive, in which case this flag may cause the PIO mode for both drives to be set.  Many IDE chipsets  support  either
              fewer  or more than the standard six (0 to 5) PIO modes, so the exact speed setting that is actually implemented will vary by chipset/driver sophis-
              tication.  Use with extreme caution!  This feature includes zero protection for the unwary,  and  an  unsuccessful  outcome  may  result  in  severe
              filesystem corruption!
      -P    Set the maximum sector count for the drive's internal prefetch mechanism.  Not all drives support this feature.
      -q    Handle  the next flag quietly, suppressing normal output.  This is useful for reducing screen clutter when running from system startup scripts.  Not
              applicable to the -i or -v or -t or -T flags.
      -Q    Set tagged queue depth (1 or greater), or turn tagged queuing off (0).  This only works with the newer 2.5.xx (or later) kernels, and only with  the
              few drives that currently support it.
      -r    Get/set read-only flag for the device.  When set, Linux disallows write operations on the device.
      -R    Register an IDE interface.  Dangerous.  See the -U option for more information.
      -S    Set  the  standby  (spindown)  timeout  for the drive.  This value is used by the drive to determine how long to wait (with no disk activity) before
              turning off the spindle motor to save power.  Under such circumstances, the drive may take as long as 30 seconds to respond  to  a  subsequent  disk
              access,  though  most  drives  are  much quicker.  The encoding of the timeout value is somewhat peculiar.  A value of zero means "timeouts are dis-
              abled": the device will not automatically enter standby mode.  Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds
              to  20  minutes.  Values  from 241 to 251 specify from 1 to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours.  A value of 252
              signifies a timeout of 21 minutes. A value of 253 sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is  reserved.  255
              is interpreted as 21 minutes plus 15 seconds.  Note that some older drives may have very different interpretations of these values.
      -T    Perform  timings  of  cache  reads for benchmark and comparison purposes.  For meaningful results, this operation should be repeated 2-3 times on an
              otherwise inactive system (no other active processes) with at least a couple of megabytes of free  memory.  This  displays  the  speed  of  reading
              directly  from the Linux buffer cache without disk access.  This measurement is essentially an indication of the throughput of the processor, cache,
              and memory of the system under test.  If the -t flag is also specified, then a correction factor based on the outcome of  -T  will  be  incorporated
              into the result reported for the -t operation.
      -t    Perform  timings  of  device reads for benchmark and comparison purposes.  For meaningful results, this operation should be repeated 2-3 times on an
              otherwise inactive system (no other active processes) with at least a couple of megabytes of free  memory.  This  displays  the  speed  of  reading
              through the buffer cache to the disk without any prior caching of data.  This measurement is an indication of how fast the drive can sustain sequen-
              tial data reads under Linux, without any filesystem overhead.  To ensure accurate measurements, the buffer cache is flushed during the processing of
              -t  using  the BLKFLSBUF ioctl.  If the -T flag is also specified, then a correction factor based on the outcome of -T will be incorporated into the
              result reported for the -t operation.
      -u    Get/set interrupt-unmask flag for the drive.  A setting of 1 permits the driver to unmask other interrupts during processing of  a  disk  interrupt,
              which  greatly  improves  Linux's  responsiveness and eliminates "serial port overrun" errors.  Use this feature with caution: some drive/controller
              combinations do not tolerate the increased I/O latencies possible when this feature is enabled, resulting in massive filesystem corruption.  In par-
              ticular, CMD-640B and RZ1000 (E)IDE interfaces can be unreliable (due to a hardware flaw) when this option is used with kernel versions earlier than
              2.0.13.  Disabling the IDE prefetch feature of these interfaces (usually a BIOS/CMOS setting) provides a safe fix for the problem for use with  ear-
              lier kernels.
      -U    Un-register an IDE interface.  Dangerous.  The companion for the -R option.  Intended for use with hardware made specifically for hot-swapping (very
              rare!).  Use with knowledge and extreme caution as this can easily hang or damage your system.  The hdparm source distribution includes a  'contrib'
              directory with some user-donated scripts for hot-swapping on the UltraBay of a ThinkPad 600E.  Use at your own risk.
      -v    Display  all  settings,  except -i (same as -acdgkmnru for IDE, -gr for SCSI or -adgr for XT).  This is also the default behaviour when no flags are
              specified.
      -w    Perform a device reset (DANGEROUS).  Do NOT use this option.  It exists for unlikely situations where a reboot might otherwise be required to get  a
              confused drive back into a useable state.
      -W    Disable/enable the IDE drive's write-caching feature (default state is undeterminable; manufacturer/model specific).
      -x    Tristate device for hotswap (DANGEROUS).
      -X    Set  the  IDE transfer mode for newer (E)IDE/ATA drives.  This is typically used in combination with -d1 when enabling DMA to/from a drive on a sup-
              ported interface chipset, where -X mdma2 is used to select multiword DMA mode2 transfers and -X sdma1 is used to select simple mode 1 DMA transfers.
              With  systems  which  support  UltraDMA  burst  timings, -X udma2 is used to select UltraDMA mode2 transfers (you'll need to prepare the chipset for
              UltraDMA beforehand).  Apart from that, use of this flag is seldom necessary since most/all modern IDE drives default to their fastest PIO  transfer
              mode  at  power-on.  Fiddling with this can be both needless and risky.  On drives which support alternate transfer modes, -X can be used to switch
              the mode of the drive only.  Prior to changing the transfer mode, the IDE interface should be jumpered or programmed (see -p flag) for the new  mode
              setting  to  prevent  loss  and/or corruption of data.  Use this with extreme caution!  For the PIO (Programmed Input/Output) transfer modes used by
              Linux, this value is simply the desired PIO mode number plus 8.  Thus, a value of 09 sets PIO mode1, 10 enables PIO mode2, and 11 selects PIO mode3.
              Setting  00  restores  the drive's "default" PIO mode, and 01 disables IORDY.  For multiword DMA, the value used is the desired DMA mode number plus
              32.  for UltraDMA, the value is the desired UltraDMA mode number plus 64.
* PIO mode
# 0 -X08 3.3MB/sec
# 1 -X09 5.2MB/sec
# 2 -X10 8.3MB/sec NEC PC-98*1
# 3 -X11 11.1MB/sec
# 4 -X12 16.7MB/sec
* Singleword DMA mode
# 0 2.1MB/sec
# 1 4.2MB/sec
# 2 8.3MB/sec
* Multiword DMA mode
# -X32 4.2MB/sec
# -X33 13.3MB/sec
# -X34 16.6MB/sec
* Ultra DMA mode
# 0 16MB/sec
# 1 25MB/sec
# 2 -X66 33MB/sec UDMA33
# 3 50MB/sec
# 4 -X68 66MB/sec UDMA66
# 5 -x69 100MB/sec UDMA100
      -y    Force an IDE drive to immediately enter the low power consumption standby mode, usually causing it to spin down.  The current power mode status  can
              be checked using the -C flag.
      -Y    Force  an  IDE  drive  to  immediately  enter  the lowest power consumption sleep mode, causing it to shut down completely.  A hard or soft reset is
              required before the drive can be accessed again (the Linux IDE driver will automatically handle issuing a reset if/when needed).  The current  power
              mode status can be checked using the -C flag.
      -z    Force a kernel re-read of the partition table of the specified device(s).
      -Z    Disable  the  automatic  power-saving function of certain Seagate drives (ST3xxx models?), to prevent them from idling/spinning-down at inconvenient
              times.


=Test delle Performance=
=Test delle Performance=
MaXeR
1 487

contributi

Estratto da "https://guide.debianizzati.org/index.php/Speciale:DiffMobile/351"

Menu di navigazione