6 999
contributi
Server per il P2P con Debian: differenze tra le versioni
→.rtorrent.rc
S3v (discussione | contributi) |
S3v (discussione | contributi) |
||
| Riga 62: | Riga 62: | ||
=====.rtorrent.rc===== | =====.rtorrent.rc===== | ||
(modifiche principali in <font style="color:red;">rosso</font>) | (modifiche principali in <font style="color:red;">rosso</font>) | ||
# This is an example resource file for rTorrent. Copy to | |||
< | # ~/.rtorrent.rc and enable/modify the options as needed. Remember to | ||
< | # uncomment the options you wish to enable. | ||
# Maximum and minimum number of peers to connect to per torrent. | |||
<span style="color:red">min_peers = 40 | |||
max_peers = 100</span> | |||
# Same as above but for seeding completed torrents (-1 = same as downloading) | |||
<span style="color:red">min_peers_seed = 5 | |||
max_peers_seed = 10</span> | |||
# Maximum number of simultanious uploads per torrent. | |||
<span style="color:red">max_uploads = 5</span> | |||
# Global upload and download rate in KiB. "0" for unlimited. | |||
<span style="color:red">download_rate = 75 | |||
upload_rate = 5</span> | |||
# Default directory to save the downloaded torrents. | |||
#directory = ./complete | |||
<span style="color:red">directory = /home/mulo/torrent/</span> | |||
# Default session directory. Make sure you don't run multiple instance | |||
# of rtorrent using the same session directory. Perhaps using a | |||
# relative path? | |||
<span style="color:red">session = /home/mulo/torrent/session</span> | |||
# Watch a directory for new torrents, and stop those that have been | |||
# deleted. | |||
<span style="color:red">schedule = watch_directory,10,10,load_start=/home/mulo/watch/*.torrent | |||
schedule = tied_directory,10,10,start_tied= | |||
schedule = untied_directory,10,10,close_untied=</span> | |||
# */ | |||
# Close torrents when diskspace is low. | |||
<span style="color:red">#schedule = low_diskspace,5,60,close_low_diskspace=100M</span> | |||
# Stop torrents when reaching upload ratio in percent, | |||
# when also reaching total upload in bytes, or when | |||
# reaching final upload ratio in percent. | |||
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0 | |||
<span style="color:red">schedule = ratio,60,60,"stop_on_ratio=250,250M,2500"</span> | |||
# Move completed torrents | |||
system.method.set_key = event.download.finished,move_complete,"execute=mv,-u,$d.get_base_path=,/home/mulo/complete;d.set_directory=/home/mulo/complete" | |||
# The ip address reported to the tracker. | |||
#ip = 127.0.0.1 | |||
#ip = rakshasa.no | |||
# The ip address the listening socket and outgoing connections is | |||
# bound to. | |||
#bind = 127.0.0.1 | |||
#bind = rakshasa.no | |||
# Port range to use for listening. | |||
<span style="color:red">port_range = 6881-6999</span> | |||
# Start opening ports at a random position within the port range. | |||
#port_random = no | |||
# Check hash for finished torrents. Might be usefull until the bug is | |||
# fixed that causes lack of diskspace not to be properly reported. | |||
#check_hash = no | |||
check_hash = yes | |||
# Set whetever the client should try to connect to UDP trackers. | |||
<span style="color:red">use_udp_trackers = yes</span> | |||
# Alternative calls to bind and ip that should handle dynamic ip's. | |||
#schedule = ip_tick,0,1800,ip=rakshasa | |||
#schedule = bind_tick,0,1800,bind=rakshasa | |||
# Encryption options, set to none (default) or any combination of the following: | |||
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext | |||
# | |||
# The example value allows incoming encrypted connections, starts unencrypted | |||
# outgoing connections but retries with encryption if they fail, preferring | |||
# plaintext to RC4 encryption after the encrypted handshake | |||
# | |||
# encryption = allow_incoming,enable_retry,prefer_plaintext | |||
<span style="color:red">encryption = allow_incoming,try_outgoing,enable_retry</span> | |||
# Enable DHT support for trackerless torrents or when all trackers are down. | |||
# May be set to "disable" (completely disable DHT), "off" (do not start DHT), | |||
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately). | |||
# The default is "off". For DHT to work, a session directory must be defined. | |||
# | |||
<span style="color:red">dht = auto</span> | |||
# UDP port to use for DHT. | |||
# | |||
dht_port = 6881 | |||
# Enable peer exchange (for torrents not marked private) | |||
# | |||
peer_exchange = yes | |||
# | |||
# Do not modify the following parameters unless you know what you're doing. | |||
# | |||
# Hash read-ahead controls how many MB to request the kernel to read | |||
# ahead. If the value is too low the disk may not be fully utilized, | |||
# while if too high the kernel might not be able to keep the read | |||
# pages in memory thus end up trashing. | |||
#hash_read_ahead = 10 | |||
# Interval between attempts to check the hash, in milliseconds. | |||
#hash_interval = 100 | |||
# Number of attempts to check the hash while using the mincore status, | |||
# before forcing. Overworked systems might need lower values to get a | |||
# decent hash checking rate. | |||
#hash_max_tries = 10 | |||
# This will set rtorrent/scgi to listen on localhost, port 5000 | |||
scgi_port = localhost:5000 | |||
# Force rtorrent to use the UTF-8 encoding. The XMLRPC standard requires UTF-8 replies | |||
encoding_list=UTF-8 | |||
La maggior parte di queste opzioni sono esplicite, altre un po' ermetiche; è possibile consultare il [http://libtorrent.rakshasa.no/rtorrent/rtorrent.1.html manuale] per avere maggiori informazioni.<br/> | La maggior parte di queste opzioni sono esplicite, altre un po' ermetiche; è possibile consultare il [http://libtorrent.rakshasa.no/rtorrent/rtorrent.1.html manuale] per avere maggiori informazioni.<br/> | ||